TV & Tuners // 8 min read

DigiTV Software Guide: Setup, EPG, Recording, Settings

DigiTV Software Guide: Setup, EPG, Recording, Settings

How do you install DigiTV and run the first channel scan?

Run Setup.exe from the install CD, restart if you have the PCI card, and DigiTV scans for channels the first time it starts. That is the sequence in the archived “DigiTV v3.5 Help” written by Nebula Electronics Ltd, the UK company that made DigiTV. This guide summarises that help and a few related pages, and it hosts no software.

The help describes screens from the Windows XP period, and the archived specification pages list Windows 2000, XP and MCE. The sections below flag where that matters.

For the PCI card, the install page says to run Setup.exe from the CD-ROM folder, follow the InstallShield prompts, then click Finish and restart. A desktop shortcut appears, and a startup entry makes DigiTV launch in “Sleep” mode each time Windows starts.

The USB master works the other way round. Per the USB master page, you install the software first, then plug in the aerial and USB cable. Windows then shows its new-hardware screen, where you choose “Install from a list or specific location”, browse to the DigiTV/drivers folder on the CD and pick “Continue Anyway” at the compatibility warning.

For the USB slave, the slave page says not to tick the shutdown option at the end of the installer, because the USB version needs no restart. You then start the program from the “DigiTV iTuner” desktop icon.

Which hardware you have is covered in the models and specs guide.

What do you do when the first scan finds no channels?

Start with the aerial. The “No Channels” troubleshooting page lists three causes: no aerial connection, a bad connection, and poor signal quality.

Its test for a bad connection is to plug a normal TV into the same aerial lead and check the picture. If the TV is fine, the page says to uninstall and reinstall DigiTV. If the TV is poor too, the page points you to the Digital Television Group postcode checker for coverage.

If the aerial is sound, the Tuning settings page has the manual controls. Autotune start and end frequencies, bandwidth and lock gate time are all adjustable. The page says that if the bandwidth does not match the transmitted one, no channels are detected even where they exist.

Lock gate time is the number of milliseconds DigiTV spends on each channel looking for a signal. The page names four locks that must all be present for detection: AGC, TPS, Viterbi and FEC. If autotune misses channels you know you can receive, it suggests raising that value and scanning again.

Two country quirks sit on the same page. DigiTV normally discards channels with a logical channel number of zero, since in the UK that means the channel carries nothing useful.

The “Tune Channels with an LCN of Zero” option keeps them and numbers them from 800. A second option adds 300 to radio LCNs for countries where radio stations reuse TV numbers.

“Set Defaults for Country” resets all the tuning values to what is stored for your country.

A different startup error is “Cannot attach to display surface”. The help page blames the graphics card being unable to show video overlays at the current resolution and refresh rate.

Its fixes are to close other overlay users such as NetMeeting, change the overlay mode on the Video settings tab, or lower the resolution or refresh rate. Its last resort is a more modern graphics card.

What do the EPG settings do, and why is the guide empty?

In the UK the programme guide arrives in the broadcast itself, so the EPG settings tab tells UK users to leave the options on “Use Live Data” and “Never auto-download EPG”. Downloading is a workaround for other countries, not something a UK setup needs.

The download options exist for countries without over-the-air listings. You set an “EPG Source” server, then choose Automatically, Manually or Never for downloads. There is also a “Download data for every day” box and a “Clear EPG Cache” button for stale schedules.

The archived page then says: “We no longer offer EPG listings for download”. It adds that several independently run servers had appeared, and that buyers should ask the shop they bought from. That snapshot dates from April 2007, and I found no archived list of those servers.

The guide itself, per the EPG overview page, runs up to 7 days ahead. You choose a channel and a date, and double-clicking a programme sets a record timer. The left panel has Listing, Search and Timer tabs.

Where does the Now and Next information come from?

You choose. The EPG settings page says that because some countries transmit unreliable Now and Next data, DigiTV lets you pick the source. “Use Live Data” takes it from the broadcast, and “Use EPG Data” takes it from the downloaded or received guide for that channel.

The Now and Next overlay appears whenever you change channel. F8 on the keyboard or the Blue key on the remote brings it up at any time.

How do you record and pause live TV in DigiTV?

Press R to record the current channel. The video recorder page says a 30-minute countdown starts, each further press of R adds 30 minutes up to a maximum of 12 hours, and S stops the recording.

DigiTV records the broadcast’s original MPEG-2 stream without recompressing it. The page puts a one-hour programme at about 1 to 1.5 GB. Files are saved as .mpg under the programme name, with a number added if the name repeats.

The default folder is a Recordings directory beneath the Nebula/DigiTV program folder. You change it under File, Settings, Recordings, General. One warning from the page: continuous recording runs until you stop it or the disk fills.

For scheduled recordings, the timer page allows up to 50 timers, and the v3.7 release notes raise the maximum to 100. Overlapping times can cut one programme short. The timers follow the PC clock, so the page suggests letting DigiTV set the clock from the TV signal.

Pausing live TV uses the same disk buffer. Per the pause page, P pauses and resumes, a counter shows how far behind live you are, and S stops buffering to disk. Disk space is used for as long as the media controls are on screen.

How do you record two channels at once?

You need more than one tuner, because one tuner receives one multiplex at a time. The multi-tuner page explains that terrestrial channels are grouped in multiplexes on different frequencies, so extra multiplexes need extra tuners.

The page names this feature iTuner and says it arrived in v3.5. DigiTV detects added tuners itself, including USB units plugged in while the program runs, and a “Devices Attached” settings page confirms what it found. Scheduled recordings use idle tuners first, and the tuner you are watching only if none is free.

Channels you cannot reach during recordings appear greyed out in the menus. The page’s own example is recording BBC1 and BBC2 by changing to each channel in turn and pressing R.

Can other programs control DigiTV?

Yes, through Windows messages. The archived third-party developers page says the messages take the form WM_COMMAND with a message ID, and gives a table of IDs and names.

The table covers general controls such as exit, digital or analogue mode, cursor movement, mute and auto-tune start and stop. It also has transport commands for record, play, pause, stop and fast forward, plus red, green, yellow and blue text buttons. Three messages take a value: set channel by order, set channel by LCN, and set volume from 0 to 50.

The page carries a no-warranty notice and was written for the v3.x era. I have not copied the ID table, and nothing here confirms that the IDs stay valid in later builds.

Does the DigiTV software run on Windows 10 or 11?

It is undocumented. The help assumes Windows XP dialogs, such as the desktop Properties screen for resolution, and the archived download page lists drivers for XP and Vista only.

Later v4 builds were sold for Windows 7, per an archived 2012 page from Nebula Media Solutions Ltd. The driver guide sets out what is known.

For a setup that works on a current PC, see the guide to watching Freeview on a PC. Release numbers are in the version history guide, and the decoding hardware for encrypted channels is in the TopUp TV guide.

DigiTV software questions

What key records a programme in DigiTV?

R. It starts a 30-minute recording, each extra press adds 30 minutes up to 12 hours, and S stops it, according to the archived video recorder help page.

Why is my DigiTV programme guide empty?

In the UK the guide comes from the broadcast, so the EPG tab should be on “Use Live Data” and “Never auto-download EPG”. The archived page says downloadable listings from the maker were discontinued, so a download setup is not a fix for a UK guide.

How much disk space does a DigiTV recording use?

About 1 to 1.5 GB per hour, because DigiTV saves the original MPEG-2 broadcast stream without recompressing it. That figure comes from the archived help for standard definition recording.

Can DigiTV pause live TV?

Yes. Press P, or the Pause key on the remote. Press S to stop buffering to disk, and note that the buffer uses disk space while it runs.

Can DigiTV record two channels at once?

Only with a second tuner on a different multiplex, or with channels sharing one multiplex. The archived help says the number of channels depends on how many tuners are installed and what each is doing.